滾筒式液壓剪切機是一種應用很廣的液壓剪切機。它裝設在連軋機組或橫切機組上，用來剪切厚度小于12mm的鋼板或小型型鋼。這種液壓剪切機作為切頭液壓剪切機時，其剪切厚度可達45mm。滾筒式液壓剪切機的刀片作簡單的圓周運動，故可剪切運動速度高達15m／s以上的軋件。圖9-1(P300頁)是滾筒式液壓剪切機結構示意圖。萬片1裝在滾筒2上(圖9-1)。滾筒2旋轉時，刀片1作圓周運動。用于切頭切尾的滾筒式液壓剪切機，在滾筒上往往裝有兩把刀片，分別用來切頭和切尾。液壓剪切機采用啟動工作制。用于切定尺的滾筒式液壓剪切機，一般采用連續工作制。小型車間的滾筒式液壓剪切機，由于軋件寬度不大，往往將刀片裝在作圓周運動的杠桿上(圖9-2) (P301頁)。圖9-2 (P301頁)所示的液壓剪切機，也稱為回轉式液壓剪切機。滾筒式或回轉式液壓剪切機的刀片作圓周運動，上下刀片切入軋件時，在垂直方向不平行，剪后軋件頭部不平整，故以剪切直徑小于Ø30mm的圓鋼或相應的方坯，以及薄板帶為宜。